Saniplus 2

  • Sale
  • Regular price $1,185.88
Saniplus 2

  • Please, ensure to select toilet style and add-on options below.

  • The original macerator for a full bathroom

    • For full bathroom applications
    • Discharge ↑ 15 Ft ↑ and/or ← 150 Ft →

    The Saniplus2 is a direct replacement for all Saniplus systems. A Saniplus is a 1/2 HP pump system used to install a complete bathroom up to 15 feet below the sewer line, or even up to 150 feet away from a soil stack. It incorporates a macerating system that can handle human waste and toilet paper in residential applications. The blade is made out of a hardened stainless steel material which eliminates the need for any service or replacement.

    The inside of the Saniplus comprises of a pressure chamber, which starts and stops the unit, and the motor, which drives the stainless steel macerator blades and the pump. When the flush is activated, the water flowing into the Saniplus activates a micro switch in the pressure chamber, which in turn starts the motor. The motor is sealed for life in an oil-filled enclosure.  A common spindle/shaft drives the impeller and the macerator blades.  The moving parts, therefore, are kept to an absolute minimum.  Water and organic waste matter enter the chamber and are reduced to slurry as the macerator blades rotate at 3600 RPM.  The centrifugal force causes the reduced solids to be ejected through a grill into the container where it is picked up by the impeller pump mounted beneath the motor.  The unit pumps the effluent upward to 15 feet and/or 150 feet horizontally (with gravity fall).  Once the water level in the container goes down, the micro switch deactivates the unit until the flush is activated again.  A normal operating cycle for Saniplus takes about 10 - 12 seconds depending upon the discharge pipe run configuration; power consumption is therefore minimal. 

    In addition to the toilet waste, the Saniplus will also discharge gray water from a variety of other sanitary fixtures such as a sink, a bathtub, a shower, and a urinal.  When adding a bathtub or shower, a base will have to be constructed.  This base should be made out of a 2" x 6" (minimum) or 2” x 8” (recommended) on edge, to allow for the installation of a P-trap and the required 1/4” per foot gravity flow towards the pump unit. 

    The wastewater from other sanitary fixtures is discharged into the Saniplus via two 2-inch inlets on either side of the housing.  Either one or both inlets can be used as required.  The discharge elbow on top of the Saniplus can be turned either to the left, to the right, or toward the back, depending on the discharge installation. A non-return valve, which comes already assembled on the discharge elbow, prevents back flow into the unit. 

    This unit has been designed with a vent connection on the lid.  All plumbing codes require a connection to a vent system.  Please note that the vent system should be a two-way air vent.  The use of mechanical vents, air admittance valves, or similar devices is not permitted as these are considered one-way air vent systems.  It is also highly recommended for the macerator/pump to be connected to a Ground Fault Interrupter (GFI) circuit.

    The design of this model consists of vibration absorbers that enable the reduction of operating sound by reducing the transmitted sounds from any location where such resonance transmission could occur.  This new design reduces the operating sound of this pump by 10 dB.

    The Saniplus unit must be connected to our rear discharge toilet.  This system uses much less water than a regular toilet.  Note: This toilet only works in combination with Saniflo systems.

    The Saniplus has been certified to American and Canadian Standards.  Macerating standard; US: CSA Certified & IAPMO (UPC) listed - ASME A112.3.4, CA: Macerating Standard CSA B45.9. 

    All items may be purchased separately.  However, the Saniplus works as a system and therefore a toilet bowl (seat included with bowl) (083 or 087), toilet tank (005), and the macerating unit (002) need to be purchased.  An optional extension pipe (030) is available for the pump to be installed behind the wall.  No cabinets, shower nor bathtub are included. 


    Sink, Toilet, Shower, Bath (sold separately)


    Dimensions (Height x Width x Depth):  10-5/8" x 20" x 7"
    Weight 18 lbs.
    Inlets (in)
    1 1/2'' vent (top) 2'' (sides)
    Power supply
    120 V - 60 Hz
    Shower/bathtub base min height
    6" min
    Noise level (measured at 3 ft.)
    ≤ 53 dBA
    Horizontal discharge
    150 ft
    Vertical discharge
    15 ft
    Amperage (Amps)
    4.5 Max
    Operating maximum temperature
    104°F (110°F Max.)
    Discharge pipe diameter
    3/4" or 1"
    Tank volume
    3 gallons
    Method of activation
    Membrane / microswitch
    Discharge rate at 3 ft
    27 gal/min (103 liters/min)
    Discharge rate at 15 ft
    17 gal/min (66 liters/min)
    Motor Speed (RPM)
     0.5 HP oil-filled thermally protected motor
    Capacitor rating (microfarad)
    Power cord length (in)
     47 1/2
    Shut off head (ft)
    Normal running time
     10-12 sec
    Certifying agencies